My Desktop PC LAN interface ( MTU 1500) Managed switch, all ports set to MTU 1500 (well, jumbo frames are off, that's the only setting) pfSense LAN adapter ( MTU 1500, also…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
ADSL VPI, VCI and Encapsulation settings. The most important information to enter to get a DSL modem working is the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) .…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
Figure out your PPPoE credentials by calling/chatting with CenturyLink. Plug in your laptop to the switch and change your laptop's IP address temporarily to 192.168.0.2 so you can connect to…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
Add up the entire payload and overhead: 1478 + 8 + 155 + 2 = 1643 bytes. 1643 bytes are transmitted for 1412 bytes of actual payload. (1452 bytes minus…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
My limited experience with CenturyLink VDSL2 is you only need VLAN 201 when you are terminating it on an unsupported (ie third party) modem. The third party modem would then…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
If you want to test your own connection, pull up the command line, run a tracert to some outside website, then start pinging the hops one by one with the…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
How to eliminate your Centurylink modem. In three easy steps. I have CenturyLink gigabit fiber with a ZyXEL C2100T modem and a WRT1900AC router with LEDE Reboot 17.01.4 r3560-79f57e422d /…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
To set one up, go to your router's app/configuration page and navigate to the wireless settings. Most routers have guest networks disabled by default, so there will usually be a…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
PPPoE connections might require special MTUsettings to function properly. Providers tell their customers if their network requires a specific MTU value—numbers like 1492 (the maximum PPPoE supports) or 1480…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
Because the MTU of the GRE tunnel is 1476, the 1500-byte packet is broken into two IPv4 fragments of 1476 and 44 bytes, each in anticipation of the additional 24…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
The setting fields differ depending on the connection type you selected. Please refer to video above or follow below steps to setup internet connection for your router. Step1: Please connect…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
For years, the standard MTU (1500 bytes) has been working fine, and it’s working well now, too. That’s because, in most cases, we deal with sub-Gigabit connections. However, when you…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
None of your results have been customized
Got it! We won't show you this again for this search.
Connect the ONT device to the USG's WAN1 port. Log in to the UniFi controller, and under devices, select your gateway->configuration->WAN, select "PPoE" from the dropdown and enter your username…
Got it! We won't show you this again for this search.
Got it! We won't show you this again for this search.
Neeva includes data from Apple, Bing, Yelp and others
